Overclocking...

Cobra · 11-15-2003, 11:07 PM

What are the guidelines to overclocking? Can you keep raising it if your temp doesnt get too high?

Emanon · 11-16-2003, 12:03 AM

OC is like dealing with a woman, its scary at times. Dont do it unless you read alot about OC in general and reports of what other people have OC your hardware in the past.

**Overlag** · 11-16-2003, 12:12 AM

That asus board should have a beginners mode where you can up it by % marks...

what cpu did you get again? the 3gig one?

**Overlag** · 11-16-2003, 12:15 AM

one thing i do want to say...even though im a overclocker is keep it at stock for a week or so first...just test it, tweak it with newer drivers etc and make sure its 100% before you even start...

will also give you more of a chance to find out stuff

Cobra · 11-16-2003, 12:36 AM

11-16-2003, 02:59 AM

Quote:

Originally Posted by Cobra

2.8c

Very nice...You'll be up to 3.5 Ghz on air with VERY few issues. I'll have a COMPLETE guide written up by tomorrow night.

Cobra · 11-16-2003, 10:08 AM

Quote:

Originally Posted by Spectre

Quote:

Originally Posted by Cobra

2.8c

Very nice...You'll be up to 3.5 Ghz on air with VERY few issues. I'll have a COMPLETE guide written up by tomorrow night.

Thx. What can I do to get better performance out of my 9800XT?

**Overlag** · 11-16-2003, 10:48 AM

IM SICK OF GETTING INVALID BLOODY SESSIONS ARRRRRRRG

Get the 3.9 Drivers from www.rage3d.com or the modded ones from www.omegacorner.com.

Make sure your Intel Chipset drivers are the latest (not sure where to find these). The default ones with WinXP might not be as fast AGP wise.

Your score is good if you had FSAAx4 and AFx8 on anyway.

but im not the expert on Intel things or how the bios's are so you'll will have to wait for spectre's guide.

11-16-2003, 11:05 AM

Quote:

Originally Posted by Spectre

Quote:

Originally Posted by Cobra

2.8c

Very nice...You'll be up to 3.5 Ghz on air with VERY few issues. I'll have a COMPLETE guide written up by tomorrow night.

Ya i need that guide too

**Overlag** · 11-16-2003, 11:12 AM

IM SICK OF GETTING INVALID BLOODY SESSIONS ARRRRRRRG

from what ive seen cobra you need this sort of settings
14 (locked) x 250mhz
Ram @ 5:4 = 200mhz with LOW latency ie 2-2-2-5 if possible.
It shouldnt need a volt increase either i dont think...not sure depends on the core. One thing, have you got HT enabled? (dual CPU ish)

you will need Prime95 and Memtest to check for instabilities... Then of corse 3dmark2001.

Cobra · 11-16-2003, 01:08 PM

Quote:

Originally Posted by Overlag

IM SICK OF GETTING INVALID BLOODY SESSIONS ARRRRRRRG

from what ive seen cobra you need this sort of settings
14 (locked) x 250mhz
Ram @ 5:4 = 200mhz with LOW latency ie 2-2-2-5 if possible.
It shouldnt need a volt increase either i dont think...not sure depends on the core. One thing, have you got HT enabled? (dual CPU ish)

you will need Prime95 and Memtest to check for instabilities... Then of corse 3dmark2001.

This is a bit over my head..can you explain..I have a P4P800D mobo

**Overlag** · 11-16-2003, 01:37 PM

erm why you get a P4P800D? thought you was getting a P4C800-E

anyway im not totaly sure about your bios, you'd need to look at the manual to find out how to change your fsb, and memory dividers.

Cobra · 11-16-2003, 01:54 PM

Quote:

Originally Posted by Overlag

IM SICK OF GETTING INVALID BLOODY SESSIONS ARRRRRRRG

from what ive seen cobra you need this sort of settings
14 (locked) x 250mhz
Ram @ 5:4 = 200mhz with LOW latency ie 2-2-2-5 if possible.
It shouldnt need a volt increase either i dont think...not sure depends on the core. One thing, have you got HT enabled? (dual CPU ish)

you will need Prime95 and Memtest to check for instabilities... Then of corse 3dmark2001.

mem is corsair 3200LLPT 2-3-2-6

**Overlag** · 11-16-2003, 02:08 PM

i remember my LLPT being sold as 2-2-2-5 but it is also listed as 2-3-2-6 grrrr

runs fine at 2-2-2-5 though

Cobra, Paul as the same board and he used the "easy" percentage settings... somewhere in the bios thers a increase clock speed thing, 10, 20, 30% etc...try it. Just make sure you know how to clear the Cmos if it goes wrong

Cobra · 11-16-2003, 02:20 PM

Quote:

Originally Posted by Overlag

i remember my LLPT being sold as 2-2-2-5 but it is also listed as 2-3-2-6 grrrr

runs fine at 2-2-2-5 though

Cobra, Paul as the same board and he used the "easy" percentage settings... somewhere in the bios thers a increase clock speed thing, 10, 20, 30% etc...try it. Just make sure you know how to clear the Cmos if it goes wrong

That is the fastest 3200 they sell...I can raise it to 20%, but if I try 30%, it crashes, and I have to flash the bios...

11-15-2003, 11:07 PM	#1 (permalink)
Cobra Join Date: May 2003 Location: Mesa Age: 32 Posts: 692	Overclocking... What are the guidelines to overclocking? Can you keep raising it if your temp doesnt get too high?

11-16-2003, 12:12 AM	#3 (permalink)
Overlag Join Date: May 2003 Location: NE Outer London, UK Age: 26 Posts: 1,540	That asus board should have a beginners mode where you can up it by % marks... what cpu did you get again? the 3gig one? __________________ From Adam Webb

11-16-2003, 12:15 AM	#4 (permalink)
Overlag Join Date: May 2003 Location: NE Outer London, UK Age: 26 Posts: 1,540	one thing i do want to say...even though im a overclocker is keep it at stock for a week or so first...just test it, tweak it with newer drivers etc and make sure its 100% before you even start... will also give you more of a chance to find out stuff __________________ From Adam Webb

11-16-2003, 10:48 AM	#8 (permalink)
Overlag Join Date: May 2003 Location: NE Outer London, UK Age: 26 Posts: 1,540	IM SICK OF GETTING INVALID BLOODY SESSIONS ARRRRRRRG Get the 3.9 Drivers from www.rage3d.com or the modded ones from www.omegacorner.com. Make sure your Intel Chipset drivers are the latest (not sure where to find these). The default ones with WinXP might not be as fast AGP wise. Your score is good if you had FSAAx4 and AFx8 on anyway. but im not the expert on Intel things or how the bios's are so you'll will have to wait for spectre's guide. __________________ From Adam Webb

11-16-2003, 11:12 AM	#10 (permalink)
Overlag Join Date: May 2003 Location: NE Outer London, UK Age: 26 Posts: 1,540	IM SICK OF GETTING INVALID BLOODY SESSIONS ARRRRRRRG from what ive seen cobra you need this sort of settings 14 (locked) x 250mhz Ram @ 5:4 = 200mhz with LOW latency ie 2-2-2-5 if possible. It shouldnt need a volt increase either i dont think...not sure depends on the core. One thing, have you got HT enabled? (dual CPU ish) you will need Prime95 and Memtest to check for instabilities... Then of corse 3dmark2001. __________________ From Adam Webb

11-16-2003, 12:03 AM	#2 (permalink)
Emanon Banned Join Date: May 2003 Age: 25 Posts: 1,249	OC is like dealing with a woman, its scary at times. Dont do it unless you read alot about OC in general and reports of what other people have OC your hardware in the past.

11-16-2003, 12:36 AM	#5 (permalink)
Cobra Join Date: May 2003 Location: Mesa Age: 32 Posts: 692	2.8c

11-16-2003, 01:37 PM	#12 (permalink)
Overlag Join Date: May 2003 Location: NE Outer London, UK Age: 26 Posts: 1,540	erm why you get a P4P800D? thought you was getting a P4C800-E anyway im not totaly sure about your bios, you'd need to look at the manual to find out how to change your fsb, and memory dividers. __________________ From Adam Webb

11-16-2003, 02:08 PM	#14 (permalink)
Overlag Join Date: May 2003 Location: NE Outer London, UK Age: 26 Posts: 1,540	i remember my LLPT being sold as 2-2-2-5 but it is also listed as 2-3-2-6 grrrr runs fine at 2-2-2-5 though Cobra, Paul as the same board and he used the "easy" percentage settings... somewhere in the bios thers a increase clock speed thing, 10, 20, 30% etc...try it. Just make sure you know how to clear the Cmos if it goes wrong __________________ From Adam Webb

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Overclocking for Dummies?	beep	Hardware & Software Discussion	9	08-22-2006 11:54 AM
Good read for those interested in Overclocking...AMD users only.	Chappie	Hardware & Software Discussion	3	02-28-2006 02:42 PM
Anyone overclocking an ATI 800xl?	TG_Trigger	Hardware & Software Discussion	0	08-11-2005 05:05 PM
Overclocking 9600pro recommend a gpu fan?	T_BEAR	Hardware & Software Discussion	9	08-17-2004 01:26 PM
Overclocking nvidia geforce4 440mx card	Buttfart	Hardware & Software Discussion	4	07-01-2004 10:05 PM

Sponsored links

Sponsored links

Sponsored links

Sponsored links